Ultrasonic Cleaning Transducer 40KHz 50W For Ultrasound Cleaner Industrial Cleaning Machine

To install an ultrasonic oscillator, it is necessary to first understand the structure and working principle of the ultrasonic oscillator. In fact, ultrasonic oscillators are also known as ultrasonic oscillators, and the overall structure of the transducer connected to the amplitude converter in the industry is calle…

Send Inquiry

Chat Now

Ultrasonic Cleaning Transducer 40KHz 50W For Ultrasound Cleaner Industrial Cleaning Machine

The ultrasonic vibrator is a device that realizes the mutual conversion of electrical energy and mechanical energy (acoustic vibration) by the Piezoelectricity of piezoelectric ceramics, and amplifies through the front and rear radiation cover blocks matched with acoustic impedance. The ultrasonic oscillator consists of an ultrasonic transducer and an ultrasonic amplitude transformer. Ultrasonic transducer is a device that can convert high-frequency electrical energy into mechanical energy. The ultrasonic amplitude transformer is a passive device that does not generate vibration itself. It only changes the amplitude of the input vibration of the ultrasonic transducer and transmits it out, completing impedance transformation.

Steps and preparation tools for installing the ultrasonic oscillator:

Preparation tools: argon arc welding, No. 10 Hex key, chrome iron tin wire, 2.5 square high temperature wire, 2 * 2.5 cable wire, vibrator glue, (Wire stripper, sleeve, binding tape, sandblasting machine, pipe fittings, etc.).
Welding screws: Calculate the arrangement position of the vibrator, weld the screws on the cleaned position, and then clean the surrounding area of the screws, making sure they are flat to avoid affecting the installation of the vibrator.
Glue configuration: Mix the glue evenly according to the specified proportion. (Meirui, Ailaoda, and 4030 glue are mixed before bonding, while KMD398 glue is mixed during the bonding process).
Installation of vibration head: Apply glue evenly to the bottom of the ultrasonic oscillator, gently twist to squeeze out the air and excess glue between the bottom of the transducer and the contact surface of the cylinder bottom, making the oscillator more tightly integrated with stainless steel.
Curing and condensation: Place it in a relatively high room temperature area for curing. It can be connected for 4-8 hours, and after 24 hours, it can be powered on for testing. The testing machine is absolutely not allowed to vibrate without air.

Note: 1. Metal nail machines can also replace argon arc welding. 2. Welding screws must be fully welded, otherwise they may fall off easily. 3. Regarding curing, the length of time should consider the temperature. If the temperature is low, the time will be longer. If the temperature is high, it will be faster. It is recommended to operate at room temperature, and even if heated, do not overheat. It is best to do so appropriately.

Type	Length（mm）	Weight（g）	Frequency（KHz）	Resonance Impedance （Ω）	Static Capacity （pF）±10%	Input Power（W）
PU-UT-20100 PZT-8	94	900	20	10-20	5200	100
PU-UT-25100 PZT-4	77	710	25	10-20	6600	100
PU-UT-28120 PZT-4	66	720	28	10-20	7800	120
PU-UT-28100 PZT-8	66	625	28	10-20	5200	100
PU-UT-28100 PZT-4	66	624	28	10-20	6600	100
PU-UT-30100 PZT-8	61	555	30	10-20	5200	100
PU-UT-2560 PZT-4	77	530	25	10-20	5400	60
PU-UT-2860 PZT-8	68	470	28	10-20	3800	60
PU-UT-2850 PZT-4	82	425	28	10-20	4100	50
PU-UT-3360 PZT-8	58	420	33	10-20	3800	60
PU-UT-4060 PZT-8	55	300	40	10-20	3800	60
PU-UT-4060 PZT-4	56	310	40	10-20	5400	60
PU-UT-4050 PZT-4	54	260	40	10-20	4100	50
PU-UT-4050-1 PZT-4	57	300	40	10-20	4100	50
PU-UT-5435 PZT-4	36	135	54	10-20	3200	35
PU-UT-6860 PZT-8	80	460	68	10-20	3800	60
PU-UT-68120 PZT-4	67	588	68	10-20	7800	120
PU-UT-8060 PZT-4	60	325	80	10-20	5400	60
PU-UT-12060 PZT-4	56	260	120	10-20	5400	60
PU-UT-13550 PZT-4	54	215	135	10-20	4200	50