High Power 28Khz 60W Piezoelectric Ceramic Ultrasonic Cleaner Transducer For Ultrasonic Cleaning Machine

When installing ultrasonic vibrators, first of all, it is necessary to understand the structure of the ultrasonic transducer vibrator and the working principle of the ultrasonic vibrator. In fact, the ultrasonic vibrator is also called the ultrasonic vibrator. In the industry, the whole body connected with the transd…

Send Inquiry

Chat Now

High Power 28Khz 60W Piezoelectric Ceramic Ultrasonic Cleaner Transducer For Ultrasonic Cleaning Machine

The ultrasonic vibrator is a device that realizes the mutual conversion of electrical energy and mechanical energy (acoustic vibration) by the piezoelectric effect of piezoelectric ceramics, and amplifies through the front and rear radiation cover blocks matched by acoustic impedance. Ultrasonic vibrator is composed of Ultrasonic Transducer and ultrasonic horn. The ultrasonic transducer is a device that can convert high-frequency electric energy into mechanical energy. The ultrasonic horn is a passive device that does not generate vibration itself. It only changes the amplitude of the vibration input by the ultrasonic transducer and then transmits it to complete the impedance transformation.

Steps and preparation tools for installing ultrasonic vibrator:

Preparation tools: argon arc welding, No. 10 hexagonal wrench, chrome iron tin wire, 2.5 square high temperature wire, 2 * 2.5 cable wire, vibrator glue, (wire stripper, sleeve, binding tape, sandblasting machine, pipe fittings, etc.).
Welding screws: calculate the arrangement position of the vibrator, weld the screws at the cleaned position, and then clean the surrounding of the screws to ensure that they are flat, so as not to affect the installation of the vibrator.
Glue configuration: Mix the glue evenly according to the specified proportion. (Meirui, Alouda and 4030 glue are mixed before bonding, and KMD398 glue is mixed during bonding).
Installation of vibration head: evenly apply glue to the bottom of ultrasonic vibrator, gently twist to squeeze out the air and excess glue between the contact surface of transducer bottom and cylinder bottom, so that the vibrator can be more closely combined with stainless steel as a whole.
Curing and condensation: place it in a place with relatively high room temperature for curing, and connect it for 4-8 hours. After 24 hours, power on and test the machine. No air vibration is allowed in the test machine.

Notes: 1. Nailing machines with metal grades can also replace argon arc welding. 2. The welding screw must be fully welded, otherwise it is easy to fall off. 3. As for curing, temperature should be taken into consideration. If the temperature is low, the curing time will be long. If the temperature is high, the curing time will be fast. It is recommended to operate at room temperature. Even if the curing is heated, it is better not to overheat.

Type	Length（mm）	Weight（g）	Frequency（KHz）	Resonance Impedance （Ω）	Static Capacity （pF）±10%	Input Power（W）
PU-UT-20100 PZT-8	94	900	20	10-20	5200	100
PU-UT-25100 PZT-4	77	710	25	10-20	6600	100
PU-UT-28120 PZT-4	66	720	28	10-20	7800	120
PU-UT-28100 PZT-8	66	625	28	10-20	5200	100
PU-UT-28100 PZT-4	66	624	28	10-20	6600	100
PU-UT-30100 PZT-8	61	555	30	10-20	5200	100
PU-UT-2560 PZT-4	77	530	25	10-20	5400	60
PU-UT-2860 PZT-8	68	470	28	10-20	3800	60
PU-UT-2850 PZT-4	82	425	28	10-20	4100	50
PU-UT-3360 PZT-8	58	420	33	10-20	3800	60
PU-UT-4060 PZT-8	55	300	40	10-20	3800	60
PU-UT-4060 PZT-4	56	310	40	10-20	5400	60
PU-UT-4050 PZT-4	54	260	40	10-20	4100	50
PU-UT-4050-1 PZT-4	57	300	40	10-20	4100	50
PU-UT-5435 PZT-4	36	135	54	10-20	3200	35
PU-UT-6860 PZT-8	80	460	68	10-20	3800	60
PU-UT-68120 PZT-4	67	588	68	10-20	7800	120
PU-UT-8060 PZT-4	60	325	80	10-20	5400	60
PU-UT-12060 PZT-4	56	260	120	10-20	5400	60
PU-UT-13550 PZT-4	54	215	135	10-20	4200	50